Emergency Leaking Tap Repair in Double Bay
1000+ five-star reviews
A tap that will not stop dripping is easy to shrug off, until you notice the water bill climbing or the basin staining green. Left long enough, a worn tap can seize on full or start weeping behind the wall where you cannot see it.
A licensed plumber sorts it properly, day or night, with the price agreed before we lift a spanner. Ring (02) 9138 6522.
- $0 Call Out Fee
- Lifetime Labour Warranty
- Licensed & Insured
- Lic #275278C NSW plumbing licence — fully insured, water and gas
- $0 Call Out Fee No charge to come out, and free quotes before you decide.
- A Real Plumber Answers Any hour, a licensed plumber picks up, never an answering machine.
- First-Visit Fix from Stocked Vans The common washers, seats and cartridges ride with us.
What You Get With Leaking Tap Repair
A tap repair runs in a set order, and here is how a visit usually goes.
- First we close off that one fixture, at its own stop tap if it has one, or the meter if not.
- Then the tap comes apart to show what has actually failed, be it a washer, a seat, an O-ring or a cartridge.
- We recut or renew the failed piece, or fit a new tap altogether when the body itself is spent.
- Back together it goes, and we run it hot and cold, confirming the flow and a clean shut-off.
- Last, we clean up and hand back the cupboard or vanity dry, the way it was before.
When Leaking Tap Repair Can't Wait
Call sooner when a handle spins without gripping and the tap will not shut, when water is escaping from the body or spindle rather than the spout, or when a hot tap has stuck open and is dumping heated water.
A steady overnight drip, or a tap that only weeps under full pressure, is annoying rather than urgent. It still pays to book it, because the seat quietly wears the whole time it leaks.
Either way, a running tap wastes more water than most people expect, and on a metered supply that quietly shows up on the next bill. Catch it early and a worn seat never gets the chance to become a whole new tap and a bigger job.
Leaking Tap Repair, the Double Bay Version
Behind the village the housing is largely solid double-brick, render and full brick, much of it Federation and Art Deco stock.
Around William Street the tapware set into those old walls tends to be compression-style, running rubber washers on brass seats that corrode and give out over time, however hard you crank the handle.
The newer apartments go the other way, with ceramic-disc mixers that quit outright but want the precise cartridge to match. Sorting out which type you have is really where the repair begins.
What Moves the Price of Leaking Tap Repair
Tap work rarely costs much, though the figure still reflects the specific job in front of us, not a flat rate. A few points shift it:
- Whether it needs a washer and seat, or a new cartridge or complete tapware.
- The style and brand of the tap, since some designer and period sets take particular parts.
- The number of taps playing up, because doing several together saves repeat trips.
- Whether a seized stop tap means isolating up at the meter instead.
Whether it turns out to be a quick washer or a complete mixer swap, we price the job you actually have, then hold that figure. The call-out is $0, and the fixed price is set and signed off before work begins.
The Callout, Step by Step
The van that answers is the van that fixes. Call any hour and we dispatch a fully stocked emergency vehicle, not a look-and-quote visit.
We carry what emergencies actually need. Fittings, valves, hot water parts, drain gear. Most repairs happen first visit because the part's already on board.
The price is fixed before we open the toolbox. Quoted plainly on-site, approved by you, then we start.
Fixed, tested, done tonight. We verify the repair under normal use and leave the job safe, not waiting on parts.
Nearly all taps are done in the single visit, with the common parts already aboard the van. In the older double-brick homes a seized stop tap can send us back to the meter to isolate, a small extra step we point out before we begin.
The NSW Rules for Leaking Tap Repair
Swapping a washer sounds like nothing, and the plainest ones are, but the moment tapware ties into your water supply it becomes regulated work under NSW law. Do it poorly and water can seep into a wall cavity or the vanity below, rotting timber and plaster where no one thinks to look.
Put a licensed plumber on it and the reseal is done to standard, holding firm under daily use rather than giving way at the next big surge. Licensing is there for precisely this: a small fix done right today so it never balloons into a costly one.
Why Trust Us With Leaking Tap Repair
Even one dripping tap still puts a real, licensed plumber on the phone with you, never a recorded message, at any hour. We fix it once, and we fix it right.
Every repair is backed by our Lifetime Labour Warranty.
We come back. No questions. No cost.
Servicing Nearby Suburbs Too
Tap and washer jobs come along wherever we go in the eastern suburbs. We look after Edgecliff, Woollahra and Rose Bay, and a tap pairs easily with hot water repairs when a unit is involved, or we can run a hidden leak check while on site.
Need It Fixed? Call Now
Why lose a whole day to a dripping tap? Ring (02) 9138 6522 and a licensed plumber comes when it suits you, with the figure agreed up front before we start.
Good questions, straight answers
Honest Leaking Tap Repair FAQs
Quick, honest answers on common tap questions below. Not covered? Ask us on the call.
Does old pipework change how leaking tap repair is done?
It can. The pre-war double-brick homes run compression tapware whose seats wear and corrode, and a seized isolation valve can force a shut-off at the meter instead, which we allow for in the quote.
What if the tap starts leaking again after we've fixed it?
That's exactly what our labour guarantee is there for. If a repair of ours doesn't hold, we return and put it right at no cost to you, so the risk stays with us, not you.
Can you fix it on the first visit?
Nearly always. The everyday washers, seats and cartridges travel with us, so most taps are done on the spot. A rare designer or heritage mixer may call for a part to be ordered in, and we flag that up front.
How do I limit the damage before the plumber gets here?
Shut the fixture's isolation valve beneath the sink if there is one, or otherwise the meter, and pop a container or towel under any live drip. Leave the space clear so we can get straight to the shut-offs.
How long will a tap job take?
Most are finished in a single visit, as the usual parts travel with us. A full tapware swap or a stuck valve adds a little, and we will show you that on-site rather than guess over the phone.
Do you cover all of Double Bay for leaking tap repair?
Yes, the whole suburb and the streets around it, at any hour. On the foreshore blocks salt-worn tap spindles are common, so there we often replace a corroded tap outright rather than nurse it, and we say so up front.